Problems with ISA Creative SB32 PnP

#1 December 8, 2005

Hi! it's my first post here at ubuntuforums.org although I read it a lot! I'm having some trouble setting up my sound card. I have installed the isapnp package, and the result from # dmesg | grep -i pnp is:

[4294672.776000] pnp: PnP ACPI init
[4294672.785000] pnp: PnP ACPI: found 13 devices
[4294672.785000] PnPBIOS: Disabled by ACPI PNP
[4294672.788000] pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
[4294672.788000] pnp: 00:02: ioport range 0xe800-0xe80f has been reserved
[4294672.788000] pnp: 00:02: ioport range 0x290-0x297 has been reserved
[4294672.790000] isapnp: Scanning for PnP cards...
[4294672.922000] pnp: SB audio device quirk - increasing port range
[4294672.922000] pnp: AWE32 quirk - adding two ports
[4294672.922000] isapnp: Card 'Creative SB32 PnP'
[4294672.922000] isapnp: 1 Plug & Play card detected total
[4294672.963000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[4294716.865000] pnp: Device 01:01.00 activated.
[4294716.865000] sb: PnP: Found Card Named = "Creative SB32 PnP", Card PnP id = CTL009C, Device PnP id = CTL0041
[4294716.865000] sb: PnP:      Detected at: io=0x220, irq=5, dma=1, dma16=5
[4294717.104000] parport: PnPBIOS parport detected.
[4294729.454000] pnp: Device 01:01.01 activated.
[4294729.482000] gameport: NS558 PnP Gameport is pnp01:01.01/gameport0, io 0x200, speed 693kHz

Then i did a # pnpdump > /etc/isapnp.conf and edited it. Here's the lines that i have uncommented.

(INT 0 (IRQ 5 (MODE +E)))
(DMA 0 (CHANNEL 1))
(DMA 1 (CHANNEL 5))
(IO 0 (SIZE 16) (BASE 0x0220))
(IO 1 (SIZE 2) (BASE 0x0330))
(IO 2 (SIZE 4) (BASE 0x0388))
(NAME "CTL009c/268720544[0]{Audio               }")
(ACT Y)

But when i run # /etc/init.d/isapnp start it says:

Board 1 has Identity dd 10 04 59 a0 9c 00 8c 0e:  CTL009c Serial No 268720544 [checksum dd]
/etc/isapnp.conf:47 -- Fatal - resource conflict allocating IRQ5 (see /proc/interrupts)
/etc/isapnp.conf:47 -- Fatal - Error occurred executing request 'IRQ 5' --- further action aborted

The strange thing is that from # cat /proc/interrupts i get:

  5:          2          XT-PIC  soundblaster

I did all that because just doing # modprobe sb io=0x220, irq=5, dma=1, dma16=5 was not working even though the module was getting loaded.

Am i doing it all wrong? Please help me :) . Sorry about my English i'm from Brazil.